Каталог

WavePro 735Zi-A

цена по запросу

шт.

Полоса пропускания 3,5 ГГц, 4 канала, частота дискретизации до 40 ГГц

Описание Характеристики Файлы

Свобода без ограничений

WavePro 7 Zi-A превосходит дру гие высокочастотные осциллографы для решения специальных задач. Все модели WavePro 7 Zi-A от 1,5 до 6 ГГц имеют входные сопротивления и 50 Ом, и 1 МОм, а модели 4 и 6 ГГц оснащены разъёмами типа ProBus и ProLink. В результате, не требуется искать и присоединять адаптер 1 МОм, когда Вы просто хотите подключить пассивный пробник для быстрого измерения низкочастотного сигнала. Дополнительный плюс, любые существующие разработки пробников LeCroy: токовые, активные, дифференциальные, высоковольтные, полностью поддерживаются.

Большее число настроек системы синхронизации позволяет обнаруживать и выделять проблемы более эффективно

Мощная комбинация широкополосной синхронизации по фронту и 10 различных интеллектуальных триггеров позволяет обнаружить проблемы быстро и сразу сфокусироваться на причинах. Большинство синхронизаций SMART позволяют делать настройки для длительностей импульсов от 200 пс. Система синхронизации для высокоскоростных шин последовательной передачи данных позволяет осуществлять синхронизацию на скоростях передачи до 3,125 Гб/сек по последовательностям длиной до 80 бит. Доступна также опция аппаратного восстановления тактовой частоты. Кроме этого, доступен полный набор из 7 типов синхронизаций для низкоскоростных шин данных (I2C, SPI, UART, RS-232, CAN, LIN, FlexRay), которые могут запускаться по логическим состояниям на этих шинах, а также содержат условия запуска по данным типа и т.д

Детектирование и захват аномалий

TriggerScan™ использует высокоскоростную аппаратную схему синхронизации и режим послесвечения экрана для захвата только требуемых сигналов и обеспечивает ответ за минуты взамен часов. И эта возможность практически не ухудшается при работе с большой памятью или на высоких частотах дискретизации. Для включения TriggerScan™, просто вызовите пользовательские или предустановленные настройки наборов запуска по фронту, SMART или синхронизации по последовательным данным (всего до 100 комбинаций). TriggerScan™ будет быстро поочередно пропускать сигнал через каждый конкретный триггер с заданным пользователем временем проверки, захватывать и отображать любые аномалии в сигнале, удовлетворяющие условиям запуска.

Опция осциллографа смешанных сигналов (MSO)

WavePro 7 Zi-A поддерживает опцию осциллографа смешанных сигналов при работе совместно с логическими пробниками MS-250 и MS-500. Они подключаются к прибору по шинам LeCroy LBUS и USB2.0, быстро и просто производят захват данных по 36 цифровым шинам с корреляцией по времени с аналоговыми сигналами. Не надо тратить время в попытках разобраться, как подключить, синхронизировать и начать работать с логическим анализатором. MS-250 и MS-500 уже полностью интегрированы в оболочку осциллографа. Кроме анализа логических состояний по параллельным шинам данных, логические пробники полезны при наблюдениях низкоскоростных последовательных сигналов, таких как тактовая частота и данные, что высвобождает аналоговые каналы для высокочастотных измерений. Обе опции дают возможность кооперировать и аналоговый, и цифровой сигнал в шаблон синхронизации 4+36 (для MS-500) и 4+18 (для MS- 250), что очень удобно при отладке параллельных интерфейсов.

LeCroy – лидер осциллографической памяти

LeCroy использует режимы, которые позволяют максимально быстро и удобно использовать осциллографическую память. WavePro 7 Zi-A с запатентованной технологией X-Stream II даёт выигрыш по быстродействию в 10-20 раз относительно других, существующих сегодня осциллографических решений. Реакция осциллографа на органы управления передней панели всегда быстрая, даже при работе с большими объёмами информации. А специально для тех пользователей, кто хочет проводить пост-обработку данных на внешнем компьютере, опционально доступна карта высокоскоростного интерфейса передачи данных 500 Мб/с. LeCroy является лидером, когда идёт речь о работе с большими объёмами памяти.

Мгновенная реакция

Наиболее длинные записи и наиболее сложный анализ сигналов легко осуществимы, вне зависимости работаете ли вы с передней панели, или предпочитаете использовать мышь. Вы заметите разницу в скорости реакции с первого включения прибора.

Для конкурирующих приборов, простой поворот ручки для изменения смещения или задержки во время работы с длинной памятью может потребовать секунд, а то и минут ожидания на ответную реакцию прибора. Если же включена простая математика, такая как вычитание каналов, то некоторые осциллографы вообще становятся болезненно медленными. Осциллографы LeCroy серии WavePro 7 Zi-A остаются быстрыми и отзывчивыми даже при сборе и обработке больших объёмов информации

X-Stream II Architecture Optimized for Fast Throughput

Дизайн серии осциллографов WavePro 7 Zi-A был оптимизирован для обеспечения максимально быстрой передачи больших объёмов записанных данных, которые характерны для сегодняшних комплексных сигналов. Архитектура потоковой передачи X-Stream II использует сегменты данных переменной длины для улучшения эффективности работы кэш-памяти процессора и быстрой обработки записей. Традиционные цифровые осциллографы, которые обрабатывают полноразмерные сигналы в одном пакете, платят за это потерей производительности. Это происходит из-за применения упрощённой архитектуры, которая не использует всех возможностей процессора. X-Stream II использует процессор Intel® Core™ 2 Quad, высокоскоростные шины данных, 64-разрядную операционную систему и до 8 Гб оперативной памяти. Таким образом, спроектирована лучшая архитектура без малейших недостатков. Вы заметите разницу, как только включите прибор.

Оптимизированная длина памяти

Опция цифровых фильтров (WPZi-DFP2)

Опция DFP2 позволяет создавать фильтры с конечной и импульсной характеристикой (КИХ), и бесконечной импульсной характеристикой (БИХ) для подавления нежелательных частотных компонентов, например, шумов, и расширяет возможности по определению важных участков сигнала. Вы можете использовать набор стандартных КИХ и БИХ фильтров или производить конструирование собственных фильтров.

Опция анализатора спектра (WPZi-SPECTRUM)

Опция SPECTRUM преобразует управление осциллографом так, как оно организовано у анализа- тора спектра – прямой ввод центральной частоты, полосы обзора и полосы пропускания или плавное изменение этих параметров. Применяйте к сигналу различную фильтрацию для просмотра в реальном времени составляющих частотных компонент. Уникальное табличное представление спектральных пиков с измерением уровней и частот.

Опции MS-250 и MS-500 позволяют преобразовать осциллограф

WavePro 7 Zi-A в осциллограф смешанных сигналов с числом логических каналов до 36. Частота дис кретизации логических каналов составляет 2 Гвыб/с (что позволяет наблюдать сигналы с частотой до 500 МГц), длина памяти 50 Мб/ канал. 36 синхронизированных по времени логических канала и 4 аналоговых канала дают Вам возможность полностью изучить любое радиотехническое устройство

Опция анализа джиттера и систем синхронизации

Пакет JTA2 используется для определения эффектов модуляции и фазового дрожания неустойчиво- го сигнала, для отслеживания изменений по времени и для выполнения измерений во временных, частотных и статистических областях. Используйте три способа просмотра джиттера (статистический, временной и частотный домены) для большего понимания истинных причин и отладки устройств. Гистограммы (статистический домен) даёт понимание статистического распределения. График слежения (временной домен) отображает временную корреляцию пиков модуляции с сигналом. БПФ (частотный домен) даёт возможность локализовать регулярный джиттер.

Опции:

Memory Options

WPZi-A-S-32

32 Mpt/Ch (64 Mpt/Ch Interleaved) Memory Option for WavePro Zi-A.

WPZi-A-L-128

128 Mpt/Ch (256 Mpt/Ch Interleaved) Memory Option for WavePro Zi-A.

WPZi-A-M-64

64 Mpt/Ch (128 Mpt/Ch Interleaved) Memory Option for WavePro Zi-A.

Miscellaneous

RACKMOUNT-1

Rack-mount accessory for converting a WavePro Zi series oscilloscope to an 8U rack-mounted package

WPZi-HARDCASE

Hard carrying case for all WavePro Zi Series oscilloscopes

TTL-AUX-OUT

Accessory for Zi oscilloscopes to enable TTL level output from the Aux Out connector

20dB-SMA-Attenuator

20 dB Attenuator

Zi-FrontPanel

Removable front panel for WavePro 7Zi and WaveMaster 8Zi Oscilloscopes

KYBD-1

Keyboard

Rise-Time-Filter-100ps

Low-Pass Rise Time Filter 100 ps

Rise-Time-Filter-150ps

Low-Pass Rise Time Filter 150 ps

SOFTCASE

Mixed Signal Accessories

HDA-DLS-09QL

9 channel QuickLink leadset for HDA125

HDA-DLS-18QL

18 channel QuickLink leadset for HDA125

MSO-DLS-36

Digital Lead Set, D18-D35

MSO-DLS-18

Digital Lead Set, D0-D17

MSO-3M

3M Interconnect Cable, D0-D17 or D18-D35

MSO-MICTOR

Mictor Cable, D0-D35

PK400-3

Small gripper probe set for 0.008'' (0.2 mm) pin pitch, includes 10 probes with color-coded leads

PK400-2

Medium gripper probe set for 0.04'' (1.0 mm) pin pitch, includes 10 probes with color-coded leads

PK400-1

Large gripper probe set for 0.10'' (2.54 mm) pin pitch, includes 10 probes with color-coded leads

PK400-0

Extra Large Gripper Probe Set . Includes 22 probes

Synchronize Oscilloscope Options

Zi-8CH-SYNCH

HW Kit to allow combination of channels from two Zi or Zi-A oscilloscopes. Allows combination of all channels from two oscilloscopes (8 channels total) or combination of all 20-30 GHz channels from two 20-30 GHz 8Zi or 8Zi-A oscilloscopes (4 channels total), or combination of 45 GHz channels

Remote Control/Network Options

GPIB-2

IEEE 488 GPIB Interface

Sampling Rate Options

WPZi-1.5GHz-4X20GS

20 GS/s (40 GS/s Interleaved) Sampling Rate Option for 1.5 GHz WavePro Zi

Computer Upgrade

WPZi-8-UPG-32GBRAM

8 GB to 32 GB CPU RAM Upgrade Option

WPZi-500GB-RHD-02

Additional 500 GB Hard Drive for WPZi. Includes Windows 7 OS, LeCroy oscilloscope software and critical scope operational file duplicates.

WPZi-500GB-HD

Upgrade from standard size hard drive to 500 GB hard drive

Serial Data Test Fixtures

TF-MIPI-MPHY-DUALPAK

MIPI M-PHY input offset adapter dual pack

TF-SATA-C-Kit

SATA Compliance Test Kit

TF-HDMI-3.3V-QUADPAK

HDMI Pull-Up Terminator Quad Pack - For Use with the Wilder-Tech HDMI-TPA-P Plug Test Adapter

TF-USB-B

USB 2.0 Compliance Test Fixture

TF-ENET-B

10/100/1000BaseT Ethernet Test Fixture

Mixed Signal Solutions

MS-250

250 MHz Maximum Input Frequency, 18 Channels, 10 Mpts/ch Mixed Signal Oscilloscope Option

MS-500-36

250 MHz Maximum Input Frequency, 36 Channels, 25 Mpts/ch Mixed Signal Oscilloscope Option

MS-500

500 MHz Maximum Input Frequency, 18 Channels, 50 Mpts/ch Mixed Signal Oscilloscope Option

HDA125-09-LBUS

12.5 GS/s High-speed Digital Analyzer with 9ch QuickLink leadset and LBUS connection

HDA125-18-LBUS

12.5 GS/s High-speed Digital Analyzer with 18ch QuickLink leadset and SYNC connection

Data Storage Software

DDM2

Disk Drive Analyzer Software Package

AORM

Advanced Optical Recording Measurements

Other Software Options

VectorLinQ VSA Package

Signal Analysis (VSA) options provide an extensive toolset for demodulation and analysis of RF and IQ modulated signals. These tools provide deep insight into advanced signal types with maximum measurement flexibility and sophisticated signal visualization. The intuitive user interface is easy to set up and allows for user customization to meet the needs of even the most complex signals.

Spectrum Analyzer Option

Spectrum analyzer style user interface with controls for start/stop frequency or center frequency and span. Utilize up to 20 markers to automatically identify harmonics and quickly analyze frequency content. Monitor how the spectrum changes over time by viewing the spectrogram in 2D or 3D.

EMC

Understanding an electronic design's susceptibility to Electronmagnetic (EM) discharge is an important element of validation. Whether fast one time event transients or repetitive bursts EM can introduce unexpected events in the circuit performance. Teledyne LeCroy Oscilloscopes offer high sample rates and measurements tailored specifically to this task. Whether one pulse or billions of measurements engineers gain insight into their device and system suseptibility.

Serial Data Analysis

VirtualProbe

By using VirtualProbe, you can understand the characteristics of signals where a physical probe cannot be placed, such as inside of a package or at the end of an interconnect that doesn't physically exist. You can choose to remove effects caused by elements such as fixtures that are not be present in a production configuration, and also add the effects of a device that is to be included but for which only an S-parameter model exists. Use in conjunction with SDAIII products to complete your serial data analysis solution set.

SDM

Serial Data Mask Package

PAM4

PAM4 signaling represents a new step in the evolution of serial data signal formats, overcoming some fundamental limitations of traditional NRZ signaling. But with new signal types come new measurement needs. Teledyne LeCroy’s PAM4 analysis package meets these needs by leveraging industry-leading eye, jitter and noise analysis capabilities to perform eye, jitter and noise analysis of PAM4 signals.

Eye Doctor II

Eye Doctor II provides the channel emulation and de-embedding tools that engineers need for the next generation of serial data standards

CBL-DE-EMBED

Remove cable effects from your measurements

SDAIII-CompleteLinQ

signaling, designers of serial data systems require multi-lane analysis. Unleash the power of multi-lane SDA analysis to perform eye and jitter measurements on up to four lanes, simultaneously.

Serial Data Compliance

QPHY-USB

The USB package provides a complete acquisition and analysis system for USB 2.0 devices, hosts, and hubs, as specified in the USB-IF USB 2.0 Electrical Test Specification. The test software implements a full set of electrical tests for USB 2.0, including High-, Full-, and Low-speed tests and is supported by Teledyne LeCroy’s QualiPHY automated test and reporting software.

QPHY-PCIe

The Teledyne LeCroy QPHY-PCIe Test Solution provides automated control for Teledyne LeCroy oscilloscopes for performing the entire transmitter physical layer tests as described by the Card Electro-mechanical specification Rev 1.1 and 2.0

QPHY-MOST50

The Teledyne LeCroy QPHY-MOST50 compliance test package provides a highly automated and easy-to-use solution to MOST compliance testing. QPHY-MOST50 will perform all electrical compliance tests as defined in the MOST Electrical Physical Layer Specification Rev. 1.1.

QPHY-MOST150

The Teledyne LeCroy QPHY-MOST150 compliance test package provides a highly automated and easy-to-use solution to MOST compliance testing. QPHY-MOST150 will perform all electrical compliance tests as defined in the MOST150 oPHY Automotive Physical Layer Sub-Specification Rev. 1.1 and MOST150 cPHY Automotive Physical Layer Sub-Specification Rev 1.0.

QPHY-MIPI-DPHY - D-PHY Compliance Package

Test Solution provides automated control for Teledyne LeCroy oscilloscopes for performing transmitter physical layer tests as described by the MIPI Alliance Specification for D-PHY version 1.00.00

QPHY-LPDDR2

The Teledyne LeCroy QPHY-LPDDR2 Test Solution is the best way to characterize LPDDR2 memory interfaces. Capable of performing measurements on 466 MHz, 533 MHz, 667 MHz, 800 MHz, 900 Mhz, 1066 MHz and custom speed grades, QPHY-LPDDR2 has a full suite of Clock, Electrical and Timing tests as specified by the JEDEC Specifications.

QPHY-HDMI2

automated and easy-to-use solution for HDMI transmitter testing in accordance with Version 2.0 of the HDMI Compliance Test Specification (including testing for version 1.4 devices).

QPHY-ENET

Ethernet testing compliant with IEEE 802.3-2005 requires many test setups and connections and mask tests. Using Teledyne LeCroy QualiPHY-ENET these measurements are easy to setup and complete. Instructive connection diagrams and message boxes appear as pop ups on the oscilloscope screen. The connection diagram instructs the user how to change test fixture and jumper pins in order to do complete test. When the tests are complete, QualiPHY will generate a test report in PDF, HTML, or XML formats. Jitter and pulse mask tests are performed with automatic waveform alignment, and all test results feature pass/fail indicators corresponding to the standard being tested.

QPHY-eDP

QPHY-eDP provides a highly automated and easy-to-use solution for Embedded DisplayPort source testing in accordance with version 1.4 of the VESA Embedded DisplayPort PHY compliance test guideline.

QPHY-DisplayPort

The QPHY-DisplayPort software option provides an automated test environment for running all of the normative real-time oscilloscope tests for sources in accordance with Version 1.2b of the Video Electronics Standards Association (VESA) DisplayPort PHY Compliance Test Specification, as well as tests for HBR3 signals at 8.1 Gbps.

QPHY-DDR3

The Teledyne LeCroy QPHY-DDR3 Test Solution is the best way to characterize DDR3, DDR3L, and LPDDR3 memory interfaces. Capable of performing measurements on 800 MT/s, 1066 MT/s, 1333 MT/s, 1600 MT/s, 1866 MT/s, 2133 MT/s and custom speed grades, QPHY-DDR3 has a full suite of Clock, Electrical, and Timing tests as specified by the JEDEC Specification.

QPHY-DDR2

The Teledyne LeCroy QPHY-DDR2 Test Solution is the best way to characterize DDR2 memory interfaces. Capable of performing measurements on 400 MHz, 533 MHz, 667 MHz, 800 MHz, 1066 MHz and custom speed grades, QPHY-DDR2 has a full suite of Clock, Electrical and Timing tests as specified by the JEDEC Specification and Intel JEDEC Specifications Addendums.

GRL-USB-PD-C1

GRL-USB-PD-C1 is a flexible test controller, designed for USB-PD Compliance testing of the Unit Under Test (UUT) and more.

GRL-USB-PD

GRL-USB-PD software provides a simple and efficient way to perform USB-PD electrical parametric and protocol measurements. GRL-USB-PD provides waveform visibility and protocol analysis making it ideal for design and debug of USB Type-C Power Delivery silicon and end products.

ET-PMT

Electrical Telecom Mask Test Package

DDR Debug Toolkit

The DDR Debug Toolkit provides test, debug and analysis tools for the entire DDR design cycle. The unique DDR analysis capabilities provide automatic Read and Write burst separation, bursted data jitter analysis and DDR-specific measurement parameters.

QPHY-BroadR-Reach

Automotive Ethernet enables faster data communication to meet the demands of today’s vehicles and the connected vehicles of the future. QPHY-BroadR-Reach automates testing and validation of 100 Mb/s Automotive Ethernet, which is described in both the BroadR-Reach and 100Base-T1 (IEEE 802.3bw) specifications.

Digital Filtering Software

DFP2

Digital Fiter Package

Jitter Analysis Software

JITKIT

Validating system jitter performance and analyzing systems with high jitter levels comprises a significant portion of a system engineer's test and validation time. JITKIT makes it simple and easy to understand the basic system jitter performance of clock signals and clock-data activities, including period, half period, cyclecycle, skew, amplitude, differential voltage crossing, slew rate, and a wide variety of other common jitter measurements.

Power Analysis Software

Power Analyzer Package

Automatically and accurately analyze the performance of switched-mode power circuits

Serial Trigger and Decode

USB2bus TD

performance triggers and transparent color-coded decode overlays, protocol tables, and search capabilities.

USB2-HSICbus D

The comprehensive and intuitive deocde and easy to navigate table display enable a powerful toolset to quickly debug a USB 2.0 HSIC powered system. Combine it with ProtoSync to get a full view of all the USB 2.0 layers.

USB 3.0 bus

The USB 3.0 decode option for Teledyne LeCroy oscilloscopes provides link layer decode information annotated on the USB 3.0 physical layer waveform. This provides the ability to view protocol traffic on the oscilloscope and verify that the link is alive and transmitting properly. It also aids in debugging problems that are not solely analog or digital in nature, such as interoperability issues, uncertain error causes, and physical layer issues not evident with a Protocol Analyzer.

UNIPRObus D

The MIPI UniPro Protocol Decoder analyzes acquired M-PHY analog waveforms and provides insight into multiple levels of UniPro protocol information. Data and Control frames are presented in an intuitive table format, where selecting a frame expands its content to a color-coded symbolic level, simultaneously creating a zoom. Decode annotation information is displayed on the physical layer waveform for a quick reference.

UART-RS232bus TDME

The UART and RS-232 Trigger Decode (TD) and Trigger, Decode, Measure/Graph and Physical Layer (TDME) solutions both provide high performance triggers and transparent color-coded decode overlays, protocol tables, and search capabilities. The TDME option also provides Measure/Graph (M) capability with automated measurement and graphing tools and Eye Diagram (E) capability for physical layer signal assessment and debug.

UART-RS232bus TD

The UART and RS-232 Trigger Decode solution provides high performance triggers and transparent color-coded decode overlays, protocol tables, and search capabilities.

SPMI Decode

The MIPI System Power Management Interface (SPMI) decoder provides a fast and easy way to understand and correlate SPMI bus traffic to DC power rails and power management IC (PMIC) operations in mobile, handheld, and battery-powered embedded systems.

SPIbus TDME

The SPI Trigger, Decode, Measure/Graph and Physical Layer (TDME) solution provides high performance triggers and transparent color-coded decode overlays, protocol tables, and search capabilities. The TDME option also provides Measure/Graph (M) capability with automated measurement and graphing tools and Eye Diagram (E) capability for physical layer signal assessment and debug.

SPIbus TD

The SPI Trigger solution provides high performance triggers and transparent color-coded decode overlays, protocol tables, and search capabilities.

SENTbus D

High-resolution SENT sensor and ECU message frames are intuitively decoded on the waveform, provided in an interactive table, and payload content search tools make debugging fast and effective.

SATA Trigger and Decode

The SATAbus TD option provides comprehensive SATA 1.5 and 3 Gb/s protocol triggering in a WaveRunner 6 Zi oscilloscope using a true hardware protocol trigger for most efficient debug.

SAS bus D

The SASbus D decode annotation option is available for most Teledyne LeCroy oscilloscopes. It permits link and data layer decoding of 1.5, 3, 6, or 12 Gb/s SAS physical layer signals. Decode information is annotated on the physical layer waveform. Various sections of the protocol are color-coded to make it easy to understand the protocol traffic.

ProtoSync

The ProtoSync option further leverages the supported Teledyne LeCroy decode annotation options (PCIEbus D, USB3bus D, USB2bus D, USB2 HSICbus D, SATAbus D, SASbus D, FCbus D) installed on the oscilloscope.

PCIe Decode

The PCIEbus D option provides comprehensive PCI Express Gen1.x protocol decode for most efficient debug.

Manchester Decode

Manchester coding is a line code in which the encoding of each data bit has at least one transition and 1s and 0s have equal bit width and therefore has no DC component. Manchester signals are self-clocking, which means that a clock signal can be recovered from the encoded data. Manchester Configurable protocol decoder enables grouping bits using various combinations of bit rate, polarity, idle condition, time out and more to decipherable messages. It allows decode of various protocols developed using Manchester encoding scheme.

M-PHYbus DP - Decode and Physical layer test option

The MIPI M-PHY and D-PHY Decode and Physical Layer Test is the ideal tool for powerful system level protocol debug as well as problem solving for signal quality issues. The D-PHY decode solution adds a unique set of tools to your oscilloscope, simplifying how you design and debug MIPI D-PHY, CSI-2 and DSI signals.

M-PHYbus D - Decode option

LINbus TDME

The LIN Trigger Decode (TD) and Trigger, Decode, Measure/Graph and Physical Layer (TDME) solutions both provide high performance triggers and transparent color-coded decode overlays, protocol tables, and search capabilities. The TDME option also provides Measure/Graph (M) capability with automated measurement and graphing tools and Eye Diagram (E) capability for physical layer signal assessment and debug.

LINbus TD

The LIN Trigger Decode (TD) solution provides high performance triggers and transparent color-coded decode overlays, protocol tables, and search capabilities.

I2Cbus TDME

The I2C Trigger, Decode, Measure/Graph and Physical Layer (TDME) solution provides high performance triggers, transparent color-coded decode overlays, protocol tables, and search capabilities, Measure/Graph capability with automated measurement and graphing tools, and Eye Diagram capability for physical layer signal assessment and debug.

I2Cbus TD

The I2C Trigger Decode (TD) solution provides high performance triggers and transparent color-coded decode overlays, protocol tables, and search capabilities.

HSPT

Option for 4-6 GHz Oscilloscopes & Disk Drive Analyzers

FlexRaybus TD

The FlexRay Trigger Decode (TD) solution provides high performance triggers and transparent color-coded decode overlays, protocol tables, and search capabilities.

Fibre Channel Decode

The FCbus D decode annotation option is available for most Teledyne LeCroy oscilloscopes. It permits link and data layer decoding of 1, 2, 4, or 8GFC (1.0625 Gb/s to 8.5 Gb/s) Fibre Channel physical layer signals.

Ethernet Decode

Ethernet Decode Ethernet decoding provides protocol awareness to the oscilloscope for fast debugging.

Embedded System Bundle TD

The Embedded Bundle Trigger and Decode (TD) contains the capabilities included in the I2Cbus, SPIbus, and UART-RS232bus TD products. For more information on this product, please see the product pages for I2Cbus TD, SPIbus TD, and UART-RS232bus TD.

DigRF v4 bus

The DigRF 3G and v4 decode are the ideal tools for powerful system level protocol debug as well as problem solving for signal quality issues. The DigRF decodes add a unique set of tools to your oscilloscope, simplifying how you design and debug MIPI digital RF systems.

DigRF 3G bus

The DigRF 3G decode is the ideal tool for powerful system level protocol debug as well as problem solving for signal quality issues. The DigRF 3G decode adds a unique set of tools to your oscilloscope, simplifying how you design and debug MIPI digital RF systems.

D-PHYbus DP - Decode and Physical layer test option

D-PHYbus D - Decode option

The MIPI D-PHY decode is the ideal tool for powerful system level protocol debug as well as problem solving for signal quality issues. The D-PHY decode solution adds a unique set of tools to your oscilloscope, simplifying how you design and debug MIPI D-PHY, CSI-2 and DSI signals.

CANbus TDME Symbolic

The CAN Trigger, Decode, Measure/Graph and Eye Diagram solution with Symbolic CAN support (TDME Symbolic) provides high performance triggers, transparent color-coded decode overlays, protocol tables, and search capabilities, Measure/Graph (M) capability with automated measurement and graphing tools, and Eye Diagram (E) capability for physical layer signal assessment and debug. Symbolic DBC files may be used to set up the trigger, display symbolic decodes, and select parameters for serial digital data extraction to an analog value

CANbus TDME

The CAN Trigger, Decode, Measure/Graph and Eye Diagram (TDME) solution provides high performance triggers, transparent color-coded decode overlays, protocol tables, and search capabilities, Measure/Graph (M) capability with automated measurement and graphing tools, and Eye Diagram (E) capability for physical layer signal assessment and debug.

CANbus TD

performance triggers and transparent color-coded decode overlays, protocol tables, and search capabilities.

CAN FDbus TDME Symbolic

The CAN FD Trigger, Decode, Measure/Graph and Eye Diagram solution with Symbolic support (TDME Symbolic) provides high performance triggers and transparent color-coded decode overlays, protocol tables, and search capabilities, Measure/Graph (M) capability with automated measurement and graphing tools, and Eye Diagram (E) capability for physical layer signal assessment and debug for both CAN and CAN FD. Symbolic DBC files may be used to set up the trigger, display symbolic decodes, and select parameters for serial digital data extraction to an analog value.

CAN FDbus TDME

The CAN FD Trigger, Decode, Measure/Graph and Eye Diagram (TDME) solution provides high performance triggers and transparent color-coded decode overlays, protocol tables, and search capabilities, Measure/Graph (M) capability with automated measurement and graphing tools, and Eye Diagram (E) capability for physical layer signal assessment and debug for both CAN and CAN FD. Symbolic DBC files may be used to set up the trigger, display symbolic decodes, and select parameters for serial digital data extraction to an analog value.

CAN FDbus TD

The CAN FD Trigger Decode (TD) solution provides high performance triggers and transparent color-coded decode overlays, protocol tables, and search capabilities for both CAN and CAN FD.

8B10B

8b10b Decode Option

1553 TDME

The MIL-STD-1553 Trigger Decode solution provides high performance triggers and transparent color-coded decode overlays, protocol tables, and search capabilities.

1553 TD

The MIL-STD-1553 Trigger Decode solution provides high performance triggers and transparent color-coded decode overlays, protocol tables, and search capabilities.

MDIO Decode

The Media Data Input/Output (MDIO) decoder provides a fast and easy way to understand and correlate MDIO bus traffic to the management of PHYs or physical layer devices in media access controllers (MACs).

AudioBus - I2S

Teledyne LeCroy’s Serial AudioBus trigger, decode, and graph package provides all the tools needed to properly analyze and debug digital audio buses. Teledyne LeCroy’s solution addresses the I2S, LJ, RJ, and TDM variations of the audio bus standard.

ARINC429bus DME Symbolic

The ARINC 429 Decode (D) and Decode, Measure/Graph and Eye Diagram (DME) options both provide Symbolic decode with transparent color-coded decode overlays, protocol tables, and search capabilities. Measure/Graph (M) provides automated protocol-specific bus performance, timing, and digital data extraction measurements and waveforms. Eye Diagram (E) provides one button eye diagram creation from the physical layer signal, various eye measurements and pass/fail indications/debug.

ARINC429bus DSymbolic

The ARINC 429 Decode (D) option provides Symbolic decode with transparent color-coded decode overlays, protocol tables, and search capabilities.

High Speed Output Accessories

LSIB-CABLE-7M

PCI Express x 4 7-meter cable with x4 cable connectors include

LSIB-CABLE-3M

PCI Express x 4 3-meter cable with x4 cable connectors included

LSIB-HOSTCARD

PCI Express x4 Express Card Host Interface for laptop Express Card slot

LSIB-HOSTBOARD

PCI Express x4 Host Interface Board for desktop PC

LSIB-1

Пробники:

Probe Parts and Kits

LPA-SMA-A

Pro-Link to SMA Adapter, new style

PACC-ZD008

Replacement Leadset for ZD200

PACC-ZD007

Replacement Accessory kit for ZD200

PACC-ZD006

Small IC adapter for ZD differential probeQty 2

PACC-ZD005

Swivel tip adapter for ZD differential probeQty 1

PACC-ZD004

Tip saver for ZD differential probeQty 2

PACC-ZD003

Long spring ground for ZD differential probeQty 2

PACC-ZD002

Solder-in lead for ZD differential probeQty 2

PACC-ZD001

Y lead Adapter for ZD differential probesQty 1

Dx20-Cable-HiTemp

Replacement 30" matched cable set for use with Dx20 HiTemp Solder tip leadset

Dx10-Cable-HiTemp

Replacement 30" matched cable set for use with Dx10 HiTemp Solder tip leadset

LPA-SMA-KIT-A

Kit of Pro-Link to SMA Adapter, new style

Dx20-SI-HiTEMP

Replacement Solder tip leadset for use with D620/D320 and temperature extension cables

Dx10-SI-HiTEMP

Replacement Solder tip leadset for use with D610/D310 and temperature extension cables

Высокоомные активные пробники

ZS1000-QUADPAK

Set of 4 ZS1000 Active Probes

ZS1500-QUADPAK

Набор из 4 пробников ZS 1500, 1,5 ГГц

ZS2500-QUADPAK

Набор из 4 пробников ZS2500, 2,5 ГГц

ZS1500

Активный пробник, 1.5 ГГц, 0,9 пФ, 1 MOм

ZS2500

Активный пробник, 2.5 ГГц, 0,9 пФ, 1 MOм

ZS4000

Активный пробник, 4.0 ГГц, 0,6 пФ, 1 MOм

ZS1000

1 GHz, 0.9 pF, 1 MOhm Active Voltage Probe

Токовые пробники

DCS025

Deskew Calibration Source for CP030, CP030A, CP031, CP031A, AP015, CP150, CP500

CP150-6M

150 A, 5 MHz Current Probe - AC/DC, 150 A rms, 500 A Peak Pulse, 6 meter cable

CP030-3M

30 A, 10 MHz Current Probe - AC/DC, 30 A rms, 50 A Peak Pulse, 3 meter cable

DCS015

Deskew Calibration Source for AP015

CA10-QUADPAK

Programmable ProBus Current Adapter

CP500

Токовый пробник до 500 А, 2 МГц

CP150

Токовый пробник до 150 А, максимум 500 A < 30 мкс, 10 МГц

CP031A

Высокочувствительный токовый пробник до 30 A, 100 МГц

CP031

Токовый пробник до 30 A, 100 МГц

CP030A

Высокочувствительный токовый пробник до 30 A, 50 МГц

CP030

Токовый пробник до 30 A, 50 МГц

Пассивные пробники

PP025-1

500 MHz Passive Probe, 5mm, 10:1, 10 MOhm

PP021-1

500 MHz Passive Probe, 2.5mm, 10:1, 10 MOhm

Оптические и электрические преобразователи

OE555

Long wavelength O/E converter

OE695G

Optical to Electrical Converter

OE525

Short wavelength O/E Converter (500-870 nm)

OE455

Long wavelength O/E Converter (950-1630 nm)

OE425

Short wavelength O/E Converter (500-870 nm)

Transmission Line Probes

PP066

7.5 GHz Low Capacitance ÷10/÷20 probe

Высоковольтный пробник с гальванической развязкой на основе технологии передачи аналогового сигнала через оптоволокно

HVFO-6M-FIBER

HVFO6m Optical Cable Acc'y

HVFO-2M-FIBER

HVFO 2m Optical Cable Acc'y

HVFO-1M-FIBER

HVFO 1m Optical Cable Acc'y

HVFO103-XMITTER

HVFO103 Spare Amp/Mod. Xmitter

HVFO100-40X-TIP

HVFO103 +/-40V (40x) Tip Acc'y

HVFO100-20X-TIP

HVFO103 +/-20V (20x) Tip Acc'y

HVFO100-5X-TIP

HVFO103 +/-5V (2x) Tip Acc'y

HVFO100-1X-TIP

HVFO103 +/-1V (1x) Tip Acc'y

HVFO103

High Voltage Fiber Optic Probe, 60 MHz Bandwidth. Includes soft-carrying case. Requires attenuating tip (ordered separately). Includes Qty. 1 1m Fiber Optic Cable

Высоковольтные дифференциальные пробники

ADP305

Высоковольтный дифференциальный пробник 1 кВ, 400 В, 100 MГц

ADP300

Высоковольтный дифференциальный пробник, 1 кВ, 400 В, 20 МГц

AP031

Высоковольтный дифференциальный пробник (÷10, ÷100), 700 В, 25 MГц

Active Voltage Rail Probes

RP4000-UFL-PCBMOUNT

Qty. 10 U.FL 3mm x 3mm PCB mounts (additional to those supplied with RP4030)

RP4000-MCX-CABLE-UFL

Qty. 3 3 GHz MCX to U.FL ultra-miniature coax cable, 8cm long (add'l to those supplied with RP4030)

RP4000-MCX-PCBMOUNT

Power/Voltage Rail Probe. 4 GHz bandwidth, 1.2x attenuation, +/-30V offset, +/-800mV

RP4000-MCX-LEAD-SI

Qty. 3 MCX 4 GHz solder-in lead accessories (additional to those supplied with RP4030), 18cm long

RP4000-BROWSER

RP4030 350 MHz Browser Tip accessory. Includes 0 Ohm (1x), 450 Ohm (10x) and 950 Ohm (20x) tips.

RP4030

Power/Voltage Rail Probe. 4 GHz bandwidth, 1.2x attenuation, +/-30V offset, +/-800mV

Дифференциальные усилители

DA1855A-RM

DA1855A with rackmount

DA1855A-PR2-RM

Rack mountable version of the DA1855A-PR2

DA1855A-PR2

2 Ch, 100 MHz Differential Amplifier with fast over drive recovery, calibrated offset, and selectable LP filters

DA101

10:1, 1 MOhm Passive Attenuator

DXC-5100

100:1, 2.5KV Passive High Voltage Probe Pair

DXC200

50 MHz low capacitance Passive Differential Probe Pair

DXC100A

Selectable 100:1 or 10:1 , Passive Differential Probe Pair

DA1855A

High-performance 100 MHz Differential Amplifier

Дифференциальные пробники (4-6 ГГц)

D620-A-CCNIST

NIST Calibration for D620-A. Includes test data.

D610-A-CCNIST

NIST Calibration for D610-A. Includes test data.

D420-A-CCNIST

NIST Calibration for D420-A. Includes test data

D410-A-CCNIST

NIST Calibration for D410-A. Includes test data.

TF-DSQ

Probe Deskew and Calibration Test Fixture

Dx20-QL-3SI

QuickLink Solder-In starter pack for use with Dx20 amplifier

Dx10-QL-3SI

QuickLink Solder-In starter pack for use with Dx10 amplifier

Dx20-SI

Replacement Solder tip lead set for D420/D620

Dx10-SI

Replacement Solder tip lead set for D410/D610

Dx20-QL

QuickLink Adapter for use with Dx20 amplifiers

Dx20-HiTemp

WaveLink Temperature Extension cables for Dx20.Includes 1 set of matched 30" high temperature cables, 1 solder tip lead se

Dx10-QL

QuickLink Adapter for use with Dx10 amplifiers

Dx10-HiTemp

WaveLink Temperature Extension cables for Dx10.Includes 1 set of matched 30" high temperature cables, 1 solder tip lead set

Dx20-PT-KIT

WaveLink Dx20-PT Adjustable Positioner Tip Kit. Includes XYZ Positioner Assembly with MechanicalInterconnects, Adhesive Kit, Connection Guides, Hand-held Wand, and Replacement Pins(Qty. 4)/Sockets(Qty. 2).

Dx10-PT-KIT

WaveLink Dx10-PT Adjustable Positioner Tip Kit. Includes XYZ Positioner Assembly with MechanicalInterconnects, Adhesive Kit, Connection Guides, Hand-held Wand, and Replacement Pins(Qty. 4)/Sockets(Qty 2).

WL-PLINK-CASE

WaveLink ProLink Platform/Cable Assembly Kit for D610, D620, D600A-AT, and Dxx30 WaveLink Probes.

WL-PBUS-CASE

WaveLink ProBus Platform/Cable Assembly Kit for D410, D420, and D300A-AT WaveLink Probes.

D600A-AT

WaveLink D600 6 GHz/4.8Vp-p Differential Amplifier Module with Adjustable Tips.

D400A-AT

WaveLink D400 4 GHz/4.8Vp-p Differential Amplifier Module with Adjustable Tips

D620-A

WaveLink D620-A 6 GHz/5Vp-p and +/-3V Offset Range Differential Amplifier Small Tip Module with Sold Small Tip Module with Solder-in, Quick Connect, and Square Pin Lead Sets, plus accessories.

D610-A

WaveLink D610-A 6 GHz/2.5Vp-p and +/-3V Offset Range Differential Amplifier Small Tip Module with So Small Tip Module with Solder-in, Quick Connect, and Square Pin Lead Sets, plus accessories.

D420-A

WaveLink D420-A 4 GHz/5Vp-p and +/-3V Offset Range Differential Amplifier Small Tip Module with Sold Small Tip Module with Solder-in, Quick Connect, and Square Pin Lead Sets, plus accessories.

D620-A-PS

6 GHz Complete Probe System with Dx20-SI Solder-In Tip (Qty. 1), Dx20-QC Quick Connect (Qty. 1), Dx20-SP Square Pin (Qty. 1), and Dx20-PT-KIT Positioner Tip Browser (Qty. 1)

D610-A-PS

6 GHz Complete Probe System with Dx10-SI Solder-In Tip (Qty. 1), Dx10-QC Quick Connect (Qty. 1), Dx10-SP Square Pin (Qty. 1), and Dx10-PT-KIT Positioner Tip Browser (Qty. 1)

D420-A-PS

4 GHz Complete Probe System with Dx20-SI Solder-In Tip (Qty. 1), Dx20-QC Quick Connect (Qty. 1), Dx20-SP Square Pin (Qty. 1), and Dx20-PT-KIT Positioner Tip Browser (Qty. 1)

D410-A-PS

4 GHz Complete Probe System with Dx10-SI Solder-In Tip (Qty. 1), Dx10-QC Quick Connect (Qty. 1), Dx10-SP Square Pin (Qty. 1), and Dx10-PT-KIT Positioner Tip Browser (Qty. 1)

Высоковольтные пассивные пробники

PPE6KV

Высоковольтный пробник , 1000:1 400 МГц, 5 MOм/50 MOм

PPE5KV

Высоковольтный пробник , 100:1 400 MГц 50 MOм

PPE4KV

Высоковольтный пробник ,100:1 400 МГц , 50 MOм

HVP120

Высоковольтный пассивный пробник 1 Вскз , 400 МГц

Дифференциальные пробники (<= 1.5 ГГц)

ZD500

Активный дифференциальный пробник 500 MГц, 1,0 пФ, ±8 V

ZD200

Активный дифференциальный пробник, 200 МГц, 3,5 пФ, 1 МОм, ±20 В

ZD1500

Активный дифференциальный пробник, 1,5 ГГц, 1.0 пФ, ±8 V

ZD1000

Активный дифференциальный пробник, 1 ГГц, 1,0 пФ, ±8 В

AP033

Дифференциальный пробник до 500 МГц

Адаптер для пробников

CA10